模板工程安全技術交底卡.doc

安全交底內容：
1、 木工安裝模板應戴安全帽。
2、 使用木工機械進行模板加工時，雙手要互相配合，不要猛拉；送料時手不宜進入臺面，按料時手不宜超過鋸口；加工短料時，應用手推棍送料。
3、 禁止利用拉桿、支撐攀登上下。
4、 模板及其支架在安裝過程中，必須設置臨時固定設施，嚴防傾覆。
5、 高處、復雜結構模板的拆除，應有專人指揮和切實的安全措施，并在下面標出作業區，嚴禁非操作人員進入作業區。
6、 嚴禁在同一垂直面上操作，拆除時應逐塊拆卸，不得成片松動和撬落或拉倒；拆除平臺、樓層板的底模時，應設臨時支撐，防止大片模板墜落，尤其是拆柱模時，操作人員應站在門窗洞口往外拉拆，更應嚴防突然全部掉落傷人。
7、 嚴禁站在懸臂結構上面敲拆底模。
8、 拆模時應防止釘子扎傷。
9、 拆模完工前，不得留下松動和懸掛的模板，拆下的模板應及時集中堆放。
10、圓盤鋸要經檢查驗收合格后才能使用。
Security cards on the table contents:
1, carpenter to install the template should be wearing helmets.
2, the use of woodworking machinery for template processing, the hands should complement each other, do not yank; not feed into the table when the hand by hand when the material should not exceed Jukou; processing of short materials, the application of push rod feed.
3, prohibits the use of rod, support to climb up and down.
4, templates and support during the installation process, you must set up a temporary fixed installations, prevent overturning.
5, height, removal of the template complex structure, shall be hand command and effective security measures, and marked in the following work areas, forbidden non-operators into the operation area.
6, is strictly prohibited in the same vertical plane operation, removal should be demolished block by block, not prying into pieces and drop or leave it loose; removal of platforms, the bottom floor plate model should be temporary support to prevent the large template fall, especially in demolition column mode, the operator should stand on window and door openings pull it out removed, but should prevent all falling suddenly hurt.
7, non-standing cantilevered structure above the bottom mold knock demolished.
8, form removal should be to prevent the nail stabbed.
9, form removal before completion, leaving no loose and hanging template, remove the template concentration should be stacked in time.
10, circular saw to pass through inspection and acceptance prior to use.
 

前往下載