燈具安裝工程技術交底-建筑安裝.doc

一、 施工準備
（一） 作業條件
1、 燈具安裝有關的建筑和構筑物的土建工程質量應符合現行的建筑工程施工質量驗收規范中的有關規定。
2、 燈具安裝前建筑工程應滿足:
（1） 對燈具安裝有妨礙的模板、腳手架必須拆除。
（2） 頂棚、地面等抹灰工作必須完成,地面清理工作應結束,房門可以關鎖的情況下安裝。
3、 在結構施工中配合土建己做好燈具安裝所需預埋件的預埋工作。
4、 安裝燈具用的接線盒口已修好。
5、 成排或對稱及組成幾何形狀的燈具安裝前應進行測量畫線。
（二） 材料要求
1、 燈具：各種燈具的型號、規格必須符合設計要求和國家標準的規定。配件齊全,無機械損傷、變形、油漆剝落、燈罩破裂和燈箱歪翹等現象,各種型號的照明燈具應有出廠合格證、“CCC”認證標志和認證證書復印件,進場時做驗收檢查井做好記錄。
2、 燈具導線:燈具配線嚴禁外露,燈具使用導線電壓等級不低于交流500V,引向每個燈具的導線線芯最小不小于1.Omm2。
3、 燈座:無機械損傷、變形、破裂等現象。
4、 塑料(木)臺:塑料臺應有足夠的強度,受力后無彎翹變形等現象。木臺應完整、無劈裂,油漆完好無脫落。
5、 吊管:鋼管做燈具吊管時,鋼管內徑不小于10mm,鋼管壁厚不小于1.5mm。
6、 吊鉤；固定花燈的吊鉤,其圓鋼直徑不小于燈具吊掛銷、鉤的直徑,不小于6mm,對于大型花燈、吊裝花燈的固定及懸吊裝置應按燈具重量的2倍做過載試驗。
7、 瓷接頭:應完好、無損,配件齊全。
支架：艱據燈具的重量選用相應規格的鍍鋅
First, construction preparation
(A) Operating conditions
1, lighting installation-related quality of construction and civil engineering structures should be consistent with the current Construction Quality Acceptance of the requirement.
2, lamps should be installed prior to construction to meet:
(1) of the lamps installed impede the template, scaffolding must be removed.
(2) ceiling, floor and other plaster work to be done, the ground clearance should be the end of the door lock can be related to install.
3, the structure of civil engineering construction has been doing a good job with lighting embedded embedded parts required for installation work.
4, installation of lamps with the junction box I have been repaired.
5, rows or symmetric geometry and composition should be conducted before installation of lamps measuring and drawing lines.
(B) material requirements
1, lamps: lamps of various models, specifications must meet the design requirements and national standards. Accessories complete, no mechanical damage, deformation, paint peeling, broken lampshades and lamp crooked Alice phenomena, various types of lighting fixtures should be factory certificate, "CCC" certification mark and certification copies, made the acceptance inspection approach Well good record.
2, lamp wires: non-exposed wiring lamps, lamp using wire AC voltage not less than 500V, lamp lead wires for each line of the smallest core is not less than 1.Omm2.
3, lamp holder: no mechanical damage, deformation, failure and so on.
4, plastic (wood) Taiwan: Taiwan should have sufficient strength plastic, mechanical deformation of no warping phenomenon. Wooden tables should be complete, without splitting, paint intact with no loss.
5, hanging tube: steel tube hanging lamps do, pipe diameter not less than 10mm, tube wall thickness is not less than 1.5mm.
6, hook; fixed lantern hook, not less than the diameter of its round lamps hanging off, hook the diameter, not less than 6mm, for large lantern, lantern fixed lifting device should be light weight and suspension of 2 times the load test done.
7, ceramic joints: to be intact, non-destructive, accessories complete.
Support: difficult choice, according to the weight of the lamp corresponding specifications galvanized
 

前往下載